ציוד נדרש
כרטיס פיתוח Arduino.מגן Ethernet
מעגל
מגן ה-Etheret מאפשר לכם לחבר את בקר ה-Ethernet של חברת WizNet לכרטיס ה-Arduino דרך ערוץ תקשורת SPI. המגן משתמש בקווים 10, 11, 12 ו-13 לתקשורת SPI עם בקר של WizNet. דגמים האחרונים של מגן ה-Ethernet כוללים גם חיבור לכרטיס זכרון microSD. בכרטיסים אלה קו מספר 4 משמש לבחירת הרכיב המתקשר על המגן (Slave Select).מגן ה-Ethernet צריך להיות מורכב על כרטיס הארדואינו ומחובר לרשת ה-Ethernet. תצטרכו לשנות את הגדרות הרשת בתוכנה כדי להתאים אותם לרשת שלכם.
שרטוט
אין צורך בשרטוט לדוגמה זו.קוד
- קוד: בחר הכל
/*
Web Server
A simple web server that shows the value of the analog input pins.
using an Arduino Wiznet Ethernet shield.
Circuit:
* Ethernet shield attached to pins 10, 11, 12, 13
* Analog inputs attached to pins A0 through A5 (optional)
created 18 Dec 2009
by David A. Mellis
modified 9 Apr 2012
by Tom Igoe
modified 02 Sept 2015
by Arturo Guadalupi
*/
#include <SPI.h>
#include <Ethernet.h>
// Enter a MAC address and IP address for your controller below.
// The IP address will be dependent on your local network:
byte mac[] = {
0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED
};
IPAddress ip(192, 168, 1, 177);
// Initialize the Ethernet server library
// with the IP address and port you want to use
// (port 80 is default for HTTP):
EthernetServer server(80);
void setup() {
// Open serial communications and wait for port to open:
Serial.begin(9600);
while (!Serial) {
; // wait for serial port to connect. Needed for native USB port only
}
// start the Ethernet connection and the server:
Ethernet.begin(mac, ip);
server.begin();
Serial.print("server is at ");
Serial.println(Ethernet.localIP());
}
void loop() {
// listen for incoming clients
EthernetClient client = server.available();
if (client) {
Serial.println("new client");
// an http request ends with a blank line
boolean currentLineIsBlank = true;
while (client.connected()) {
if (client.available()) {
char c = client.read();
Serial.write(c);
// if you've gotten to the end of the line (received a newline
// character) and the line is blank, the http request has ended,
// so you can send a reply
if (c == '\n' && currentLineIsBlank) {
// send a standard http response header
client.println("HTTP/1.1 200 OK");
client.println("Content-Type: text/html");
client.println("Connection: close"); // the connection will be closed after completion of the response
client.println("Refresh: 5"); // refresh the page automatically every 5 sec
client.println();
client.println("<!DOCTYPE HTML>");
client.println("<html>");
// output the value of each analog input pin
for (int analogChannel = 0; analogChannel < 6; analogChannel++) {
int sensorReading = analogRead(analogChannel);
client.print("analog input ");
client.print(analogChannel);
client.print(" is ");
client.print(sensorReading);
client.println("<br />");
}
client.println("</html>");
break;
}
if (c == '\n') {
// you're starting a new line
currentLineIsBlank = true;
} else if (c != '\r') {
// you've gotten a character on the current line
currentLineIsBlank = false;
}
}
}
// give the web browser time to receive the data
delay(1);
// close the connection:
client.stop();
Serial.println("client disconnected");
}
}
ראו גם:
מדריך לתחילת העבודה עם מגן Ethernet (אנגלית) - TODOספריית Ethernet
ChatServer - יצירת שרת צ'ט פשוט
AdvancedChatServer - שרת שמעביר את הנתונים לכל הלקוחות המחוברים חוץ מזה ששולח אותם
WebClient - שולח בקשות HTTP
WebClientRepeating - חוזר על שליחת בקשות HTTP
BarometricSensorWebServer - מציג תוצאות של חיישן לחץ ברומטרי כעמוד WEB
UDPSendReceiveString - קבלה ומשלוח הודעות טקסט דרך UDP
UdpNtpClient - קבלת זמן משרת NTP (שרת Network Time Protocol)
DnsWebClient - צד ב-Client שמבוסס על DHCP ו-DNS
DhcpChatServer - שרת צ'ט פשוט שמבוסס על DHCP
DhcpAddressPrinter - מקבל כתובת דרך DHCP ומדפיס אותה
TelnetClient - צד ה-Client פשוט לחיבור ל-Telnet
פירוט שפת תכנות לסביבת Arduino
עמוד זה הוא תרגום של WebServer לפי רישיון Creative Commons Attribution-ShareAlike 3.0.